Das Fahrzeug steht aufgebockt Räder frei
Motor läuft Gang eingelegt Vollgas und beim Gas wegnehmen geht die Warnblinkanlage an.
Was kann das sein?
Und die zweite Frage wie stellt man den Service zurück?
Danke vorab Marco
Chatenet ch26 Warnblinker
Moderatoren: guidolenz123, Fichte
- HerrToeff
- Beiträge: 11701
- Registriert: Do 14. Jan 2016, 11:18
- Fahrzeuge: Aixam 400 , Sachs zx 50, erste Serie-
D-truck 400, Schwalbe, letzte Serie- u.a. - Kontaktdaten:
Re: Chatenet ch26 Warnblinker
Bei mir müssen zum Zurückstellen beide Türen geöffnet sein. Dann Zündung an und 6sec warten, dann beide Stellstäbe drücken und warten bis die Meldung "Reset" erscheint
Das mit der Warnblinkanlage klingt wieder mal nach einem Defekt des Kombiinstruments
ich hasse das Ding
Das mit der Warnblinkanlage klingt wieder mal nach einem Defekt des Kombiinstruments
ich hasse das Ding
lieben Gruß
PN werden evtl mit starker Verzögerung beantwortet, ich bin zur Zeit nicht täglich online
PN werden evtl mit starker Verzögerung beantwortet, ich bin zur Zeit nicht täglich online
Re: Chatenet ch26 Warnblinker
Hello. Have you solved hazard warning lights come on when you start moving issue? Can you please share how?
Best Regards,
Aras
Aras
- Fichte
- Beiträge: 3745
- Registriert: Sa 21. Dez 2019, 12:47
- Fahrzeuge: Microcar, Virgo II, Luxe
Ligier, Nova 500
Bellier, „Diva“
Aixam 400 - Wohnort: Mindelheim
Re: Chatenet ch26 Warnblinker
Hey, maybe this works:
https://www.scegliauto.com/de/video/var ... e_vignette
Zuerst steigen wir in das Auto ein und beginnen mit dem Drücken und Halten der beiden Knöpfe, die wir auf der Instrumententafel finden; Dann schalten wir das Panel ein und warten, bis die auf dem Display angezeigten Kilometer zurückgesetzt werden, wie im Video gezeigt. An dieser Stelle werden wir die Instrumententafel ausschalten und dann den Motor einschalten, um zu überprüfen, ob die Serviceleuchte erloschen ist!
First we get into the car and start by pressing and holding the two buttons that we find on the dashboard; Then we turn on the panel and wait for the kilometers shown on the display to reset, as shown in the video. At this point we will turn off the instrument panel and then turn on the engine to check if the service light has gone out!
U_Tube: https://youtu.be/ZZ82qp6HEZM
https://youtu.be/ZZ82qp6HEZM
Urteile nie über einen anderen, bevor Du nicht einen Mond lang in seinen Mokassins gelaufen bist.
Re: Chatenet ch26 Warnblinker
Hello,
I forgot to mention that I have a Chatenet CH26 V1 2010.
And the thing that starts flashing after I put the car in Forward or Reverse (also tried moving the car on Neutral - it also starts flashing, but it seems to need to catch some "vibration" to activate) - it's not the "hazard warning light" - turn signal indicators on the dashboard are not blinking, neither indication on the hazard warning switch. Only the Turn Signals Blinkers start flashing. Plus, the doors unlock. Seems related to 26.00.018 Remote control + receiver set - mine is NOT ORIGINAL. The original relay should have been MQFCH1.0. If I remove this relay, the flashing after starting stops, but without that relay the central locking is disabled = no ability to lock the right door or trunk.
I read in INSTRUKCJA OBSŁUGI CH26.
During emergency braking:
- the hazard warning lights turn on automatically for 10 seconds at a speed of less than 20 km/h,
- the doors unlock automatically for security purposes.
Not sure if this feature is implemented in version 1 of Chatenet CH26?
Question: How does Chatenet CH26 recognize an “emergency” braking? Does it have an accelerometer sensor? Chatenet CH26 V1 has neither ABS nor central computer...
Thank you in advance for any response. It can be in German, no need to translate...
I forgot to mention that I have a Chatenet CH26 V1 2010.
And the thing that starts flashing after I put the car in Forward or Reverse (also tried moving the car on Neutral - it also starts flashing, but it seems to need to catch some "vibration" to activate) - it's not the "hazard warning light" - turn signal indicators on the dashboard are not blinking, neither indication on the hazard warning switch. Only the Turn Signals Blinkers start flashing. Plus, the doors unlock. Seems related to 26.00.018 Remote control + receiver set - mine is NOT ORIGINAL. The original relay should have been MQFCH1.0. If I remove this relay, the flashing after starting stops, but without that relay the central locking is disabled = no ability to lock the right door or trunk.
I read in INSTRUKCJA OBSŁUGI CH26.
During emergency braking:
- the hazard warning lights turn on automatically for 10 seconds at a speed of less than 20 km/h,
- the doors unlock automatically for security purposes.
Not sure if this feature is implemented in version 1 of Chatenet CH26?
Question: How does Chatenet CH26 recognize an “emergency” braking? Does it have an accelerometer sensor? Chatenet CH26 V1 has neither ABS nor central computer...
Thank you in advance for any response. It can be in German, no need to translate...
Best Regards,
Aras
Aras